日本特级淫片免费看-日本特级黄色-日本特级黄录像片-日本视频中文字幕-成年偏黄网站站免费-成年人福利

求5倉脈沖除塵程序，謝謝了！

怎么沒人會做呀？

說清楚你要用什么控制？？？？？？？？

用三菱fx1n

第一倉提升閥通電6s  第一倉脈沖閥通電0.7s 一次  過4s提升閥斷電 5個倉循環

按順序控制 很簡單的

第一倉提升閥通電6s ， 第一倉脈沖閥通電0.7s 一次 ， 過4s提升閥斷電， 過2min第二倉提升閥通電。。。。。。  5個倉循環。5樓能不能幫我做一下，不勝感激。

朋友：是提升閥通電6S后，脈沖閥通電0.7S，脈沖閥斷電4S后，提升閥斷電，再過2min到下一倉。提升閥總共通電10.7S，用步進指令的話，很容易。我們互相學習。

謝謝關注，能不能麻煩一下，幫我做一個。

其實很簡單。只要你用心做一下，只有經歷過才會積累經驗。

實在不好意思，步進指令我一點不懂。慚愧。

X0----------------接停止按鈕的常閉接點                    X1----------------接起動按鈕的常開接點
Y0----------------第一倉提升閥                            Y1----------------第一倉脈沖閥
Y2----------------第二倉提升閥                            Y3----------------第二倉脈沖閥
Y4----------------第三倉提升閥                            Y5----------------第三倉脈沖閥
Y6----------------第四倉提升閥                            Y7----------------第四倉脈沖閥
Y10--------------第五倉提升閥                            Y11---------------第五倉脈沖閥
LD              M8002                                                                                                                              
ORI            X0                                                                                                                                      
ZRST        S3        S30                                                                                                                      
SET           S3                                                                                                                                      
STL            S3                                                                                                                                                
LD               X0                                                                                                                                      
AND            X1                                                                                                                                      
SET             S20                            


STL             S20                         STL             S22                              STL             S24                
OUT           Y0                             OUT           Y2                                  OUT           Y4                            
OUT           T1      K107             OUT           T1      K107                  OUT           T1      K107
OUT          T2      K60                 OUT          T2      K60                     OUT          T2      K60      
LD             T2                             LD             T2                                   LD             T2  
OUT          T3      K7                   OUT          T3      K7                        OUT          T3      K7  
ANI            T3                              ANI              T3                                  ANI             T3  
OUT         Y1                               OUT            Y3                                  OUT           Y5            
LD             T1                             LD             T1                                     LD             T1                    
SET           S21                         SET           S23                                 SET           S25                      
STL            S21                       STL            S23                                  STL            S25                          
OUT        T4      K1200           OUT        T4      K1200                      OUT        T4      K1200              
LD            T4                             LD            T4                                       LD           T4            
SET         S22                           SET          S24                                    SET         S26                  
                                                                                                                                                                

STL             S26                         STL             S28                                    
OUT           Y6                             OUT           Y10                                          
OUT           T1      K107             OUT           T1      K107        
OUT          T2      K60                 OUT          T2      K60                
LD             T2                             LD             T2                                
OUT          T3      K7                   OUT          T3      K7                    
ANI            T3                              ANI              T3                              
OUT         Y7                               OUT            Y11                                    
LD             T1                             LD             T1                                              
SET           S27                         SET           S29                                            
STL            S27                       STL            S29                                                  
OUT        T4      K1200           OUT        T4      K1200                          
LD            T4                             LD            T4                              
SET         S28                           OUT          S20                                                      
                                                  RET                                                        
                                                  END                                
以上的程序供參考